Tankless Water Heater Maintenance DIY Tips

The presence of a water heater is quite common in recent days, and hence every user must pay thoughtfulness to the maintenance of this product. Most of the users of water of heater are unaware of proper processes of protecting this device. Well, no such hard techniques are to follow. It is just necessary to get an idea of some simple and secure methods for up-keeping of this product.

At first, it is necessary to know how these water heaters work. Water is pumped into this device, and hence, usually, dirt or sediments will settle on the bottom of the heater. You may also notice that some extra ingredients will be added depending on the quality of water. In such a case, it is necessary to clean the additional components immediate to avoid huge expenses in the long run. To end the task, you will need to have one hose, a bucket, and gloves for protection.

Here you can take some simple guidelines for better protection of the water heater.

  • It is necessary to place a shut-off valve so that water cannot get seized.
  • If you want to install a gas water heater, then you need to set a gas valve. This valve will keep away the burners during the flushing process. Other than gas heaters if you are willing to use the electric one, then the circuit breakers are required to be turned off during the maintenance process.
  • Users of gas heaters must pay attention that the chimney works perfectly to flow the air. While you will light a match, you need to watch whether the smoke is going up or not.
  • Now, it is the correct time to test the relief of the temperature. To examine what you need to keep a bucket just below the extension pipe and the valve is to be opened. Till the valves are kept open, the water should have flowed properly. As soon as the valves are closed, the rain should stop flowing. To check the recommended setting, you need to set a thermostat.
  • Another important point on which you need to pay attention is the pilot light. The pilot light must remain steady, and it should turn blue.
  • Now it is necessary to check whether the burners are operating correctly or not and you can do this by removing the shield. To do that you will also need to turn up the thermostat and take a look at the flames are burning blue or steady.
  • While carrying on the sediment cleaning process, it is necessary to use a garden hose and fix it to the bottom of the drain valve. Another end is to be attached to the drain near to the floor.

During the cleaning process, it is also necessary to follow some safety tips. Every user must be careful as the water will remain boiling. You should not forget to turn down the thermostat so that the supply of the cold water can get stopped. You should keep the pressure relief valve opened, and by lifting the lever, it is necessary to keep the thermostat opened.

Well, those above are some essential DIY tips for water heater maintenance.

Is Basement Safe While Having A Sump Pump?

It is essential to check the basement of a house before buying a sump pump. There are specific problems in the basement that can take a bigger shape in the future. The most common one is the problem of flooding. You cannot avoid it, and every year during the rains you will face the same problem if you do not take care of it. One of the best methods to solve this severe problem of flooding is to install a sump pump. A sump pump will protect the basement of your house from flooding.

Know about sump pumps

A sump pump is a water pumping system that is fitted either below or above the floor of the basement. It is used to remove the water that has got collected in the sump basin. The excess water may enter through the sewage system of the house or may be the result of excessive rainfall. There are also cases where the basement of the house is below the water level of the surroundings. It can result in the accumulation of water in the basement throughout the year. Sump pumps can be a great rescuer for you if the basement of your house suffers from flooding and thus results in dampness. These pumps throw out the water leaving your home dry.

There are two types of sump pump, namely pedestal and submersible. In pedestal sump pumps, the motor is placed above the sump basin. In the case of submersible pumps, the engine is entirely inside the sump basin. Pedestal pumps are less expensive in comparison to submersible pumps and last longer than the later. On the other hand, the submersible pumps help remove the suspended dirt along with the excess water.

How does a sump pump ensure the safety of the basement?

Sump pumps can be of great help in safeguarding your house against specific threats. These pumps can set your home free from any water clogging. Whether there is little water clogged or a flood of water in the basement, switching on the best sump pump can make your job easy.

Stagnant water in the basement of the house can be very harmful and can damage the quality of the building. It can also harm your belongings that rest there. Therefore install a sump pump if you are facing any such problem.

The sump pumps can also prevent short circuits and breaking of a fire in the house. Flooding in the basement can result in a short course, which may lead to a dangerous fire. Therefore sump pumps are beneficial in that way too.

Thirdly, the dampness in the basement can be a favorite place for molds to breed. It can be a severe threat to the residents of the house. Pumping out the excess water with a sump pump can keep your basement damp-free and protect your home.

Therefore if you have a damp basement then switch to using sump pump and safeguard your basement from any possible threat.

Different Taps In The Kitchen

The tap is central to any kitchen. You can skimp on a lot of things when designing your house but this should not be one of them. It is so important for daily activities that it merits those extra pounds, if need be. Go for a trusted manufacturer with a long warranty and high quality materials. You want something that will not corrode so easily as rust will affect the colour, taste, and smell of the water coming out of it. There are several designs that you can choose from. They will differ in their combinations of faucet, valves, and mounting points.

Get more info on kitchen sink taps

Single Lever Mixer

This is the most basic design with a single faucet for the water to come out of, a single valve to control the flow, and a single mounting point to simplify the installation. In some designs, the faucet and the valve are separate so there are two mounts. If you don’t want a complicated system, then this is for you. You can save space on your counter, as well as time and effort. It is perfect for people who love to do things by themselves. You could upgrade your current setup without hiring a contractor by purchasing this kind of tap.

Bridge Mixer

One of the disadvantages of the single lever mixer is the lack of options. If the only valve or mounting point happens to fail for whatever reason, then you will not be able to use the whole tap at all. There could be a blockage that will prevent you from washing your hands or preparing food. There might be a leak that will lower the pressure and waste a great deal of water. You will have to have to pay higher monthly bills or even deal with kitchen flooding. With a bridge mixer, there is only one faucet but there are two valves and mounting points so you have another option. Just close the faulty one in the meantime. This setup is also great for mixing hot and cold water.

Pillar Taps

For the ultimate in redundancy, you could have two of each vital component in your kitchen tap. Have double the number of faucets, valves, and mounting points to eliminate all worries. It isn’t that much harder to install compared to bridge mixers although you do have to create two holes instead of one on the counter. The valves are usually found on the top of the assembly. It is a good setup to have if you want separate faucets for hot and cold water instead of mixing them.

Note that there are a lot of units in which the faucet can be pulled out for a versatile spray. This is great if you are washing something heavy or delicate that you cannot move around too much. You can move the spray instead as the hose is long and flexible enough for the job. Some tap models have both a regular faucet and a pull-out spray for the utmost in versatility.